Jump to content
Annons

RAM till MBP late 2008 15"


nilsemil

Recommended Posts

Annons
tack noztra, hur var det nu, kan jag dra nytta av 6 GB? två 3 GB?

Emil

Inte helt hundra om du kan ha 2st 3GB-minnen, har inte sett 3gb minnen, men du kan ha 2st 2gb=4GB enligt teknisk information

Teknisk information, för MacBook Pro [15", Late 2008]

http://support.apple.com/kb/SP499?viewlocale=sv_SE

Redigerat av noztra
Link to comment
Dela på andra sajter

nån av dessa bättre eller sämre?

Kingston

Kingston ValueRAM DDR3 PC8500/1066MHz CL7 2GB 377:-

Crucial

Crucial DDR3 PC8500/1066MHz CL7 2GB

Kingston gör bra minnen och det gör Crucial oxå! om du har 2gb och vill uppgradera till 4 gb, så rekommenderar jag att du skaffar dig 4GB, från samma tillverkare. You can add two 2 GB memory modules for a maximum of 4 GB of memory. For best performance, fill both memory slots and install an identical memory module in each slot.

kontakta Apple för att vara helt hundra hur mycket minnen du kan ha i just din modell.

http://www.dustinhome.se/pd_5010212367.aspx

-------------------------------------------------------------------------------------------------------------------------------

Your computer has two memory slots that you can access by removing the battery and bottom case. Your MacBook Pro comes with a minimum of 2 gigabytes (GB) of 1066 MHz Double Data Rate (DDR3) Synchronous Dynamic Random-Access Memory (SDRAM) installed. Each memory slot can accept an SDRAM module that meets the following specifications:

  • Double Data Rate Small Outline Dual Inline Memory Module (DDR3) format
  • 30mm (1.18 inch)
  • 1 GB or 2 GB
  • 204-pin
  • PC3-8500 DDR3 1066 MHz type RAM

You can add two 2 GB memory modules for a maximum of 4 GB of memory. For best performance, fill both memory slots and install an identical memory module in each slot.

Removing or Installing memory:

Step 1: Remove the access door

  1. Shut down your MacBook Pro. Disconnect the power adapter, Ethernet cable, security lock, and any other cords connected to the MacBook Pro to prevent damaging the computer.
  2. Turn over your MacBook Pro and locate the latch. Push down to release the latch and remove the access door that covers the battery and hard drive.
  3. The latch must be in its released, open position to remove the access door.

HT1270-11a.png

Step 2: Remove the battery

With the latch still in its open position, gently pull up on the tab to remove the battery.

HT1270-12a.png

Step 3: Remove the bottom case

  1. Remove the eight (8) screws that secure the bottom case of your MacBook Pro, and then remove the bottom case. Important: Because the screws are different lengths, note the screw lengths and locations so you can replace the screws correctly. Put them aside in a safe place.
    HT1270-13a.png
  2. Touch a metal surface inside the computer to discharge any static electricity from your body.
    HT1270-14a.png

Step 4: Remove existing memory (if present)

  1. Push out the ejection levers on the sides of the memory module to release the module from the memory card slot. The memory pops up at an angle. Before removing it, make sure you can see the half-circle notches. If you don't, try pressing the ejection levers again.
  2. Hold the memory module by the notches and remove it from the slot.
  3. Remove the other memory module.
    Important: Hold the memory modules by their edges; do not touch the gold connectors.

HT1270-15a.png

Step 5: Install memory

  1. Align the notch on the gold edge of the module with the notch in the lower memory slot.
  2. Tilt the card and push the memory into the slot.
  3. Use two fingers with firm, even pressure to push down on the memory module. You should hear a click when the memory is inserted correctly.
  4. Repeat, if necessary, to install an additional memory module in the top slot. Press down on the module to make sure it is level.
    Note: Make sure your memory is installed according to the illustration below, with the gold contacts inserted almost completely into the connector.

HT1270-16a.png

Step 6: Replace the bottom case

Replace the bottom case. Replace and tighten the eight screws.

HT1270-17a.png

Step 7: Replace the battery

To replace the battery, make sure the latch is in its open position. Hold the battery at an angle and slide the lipped edge of the battery below the brackets on the outside edge of the battery bay. Gently press the battery down.

Step 8: Replace the access door

With the latch in the open position replace the access door, making sure it is level with the bottom case of your MacBook Pro, and press the latch into the closed position.

HT1270-18a.png

Redigerat av noztra
Link to comment
Dela på andra sajter

Du kan ha 6 gig i datorn (2+4), men Macbook pro late 2008 är väldigt känslig för vilka minnen som sitter i, fel minnen ger grafikfel och får datorn att krascha, bl.a. Kingston Valueram kan ge sådana icke önskvärda effekter. Se till att köpa minnen som testats för Mac för att vara absolut säker, t.ex. http://www.dustinhome.se/pd_5010212367.aspx

intressant. vet du vilka som är billigast 4 gb som funkar?

jag har nog ingen brådska än på ett tag. testade lite VMWARE och då hade det behövs annars är det ok.

Emil

Link to comment
Dela på andra sajter

Bli medlem (kostnadsfritt) eller logga in för att kommentera

Du behöver vara medlem för att delta i communityn

Bli medlem (kostnadsfritt)

Bli medlem kostnadsfritt i vår community genom att registrera dig. Det är enkelt och kostar inget!

Bli medlem nu (kostnadsfritt)

Logga in

Har du redan en inloggning?
Logga in här.

Logga in nu
×
×
  • Skapa ny...